Onderstaande post heb ik ook al op het forum van Minddigger.com geplaatst een week geleden maar daar heeft nog niemand op gereageerd om me te helpen. Dus probeer ik het hier ook eens.
-----------

Ik heb hier een Mitel 6.0 Server draaien met daarin een een HP Colorado 5GB IDE tapedrive.
Tijdens het opstarten van de server zie ik dat hij in de bios wordt gevonden en ook later bij het starten van SME.

Maar als ik de tapebackup heb ingesteld en een backup wil maken krijg ik de melding

Input/Output error

Nu heb ik al flexbackup -newtape volgens deze thread gedaan
http://forum.minddigger.com/phpBB/vi...4597&forum=9&5

omdat dit ook een ide tapedrive was.

Maar dan krijg ik de melding dat het scsi device niet gevonden wordt maar het is toch ook een ide device ???

Ik volg het nu even niet meer. Ik heb al verder gezocht op het forum maar dan is het meestal voor scsi. Heb er wel 1 gevonden die ide is maar die zou standaard gevonden moeten worden dus aan die thread heb ik helaas niks.

EDIT://
Output van commando dmesg:


[root@sme root]# dmesg
Linux version 2.4.20-18.7 (bhcompile@stripples.devel.redhat.com) (gcc version 2.96 20000731 (Red Hat Linux 7.3 2.96-113)) #1 Thu May 29 08:32:50 EDT 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ffc000 (usable)
BIOS-e820: 0000000007ffc000 - 0000000007fff000 (ACPI data)
BIOS-e820: 0000000007fff000 - 0000000008000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
127MB LOWMEM available.
On node 0 totalpages: 32764
zone(0): 4096 pages.
zone(1): 28668 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=Mitel-SME-up ro root=303 BOOT_FILE=/boot/vmlinuz-2.4.20-18.7
Initializing CPU#0
Detected 702.644 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1402.47 BogoMIPS
Memory: 125092k/131056k available (1175k kernel code, 4556k reserved, 986k data, 120k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf08c0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router PIIX [8086/7110] at 00:04.0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS1 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
floppy0: no floppy controllers found
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta3-.2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 00:04.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hdaMA, hdbMA
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdcMA, hddio
hda: SAMSUNG SV1022D, ATA DISK drive
hdb: CD-ROM 52X/AKH, ATAPI CD/DVD-ROM drive
blk: queue c0378440, I/O limit 4095Mb (mask 0xffffffff)
hdc: HP COLORADO 5GB, ATAPI TAPE drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 19931184 sectors (10205 MB) w/480KiB Cache, CHS=1240/255/63, UDMA(33)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 hda3
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 121k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 120k freed
Adding Swap: 265064k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 08:52:36 May 29 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 5 for device 00:04.2
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
hdb: attached ide-cdrom driver.
hdb: ATAPI 52X CD-ROM drive, 192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
SCSI subsystem driver Revision: 1.00
hdc: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: HP Model: COLORADO 5GB Rev: 2.03
Type: Sequential-Access ANSI SCSI revision: 02
st: Version 20030406, bufsize 32768, max init. bufs 4, s/g segs 16
Attached scsi tape st0 at scsi0, channel 0, id 0, lun 0
hdb: DMA disabled
hdc: DMA disabled
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (1023 buckets, 8184 max) - 292 bytes per conntrack
PCI: Found IRQ 10 for device 00:0b.0
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
00:0b.0: 3Com PCI 3c905C Tornado at 0xd000. Vers LK1.1.18-ac
00:01:02:20:30:26, IRQ 10
product code 4552 rev 00.13 date 05-10-00
Internal config register is 1800000, transceivers 0xa.
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 782d.
Enabling bus-master transmits and whole-frame receives.
00:0b.0: scatter/gather enabled. h/w checksums enabled
divert: allocating divert_blk for eth0
NET4: AppleTalk 0.18a for Linux NET4.0
[root@sme root]#


JKW