Heb trouwens vandaag de HP 1800 ook maar aangeschaft![]()
Likes: 0
Ik lees net op de HP site dat deze uit de productie genomen zijn.
http://h10010.www1.hp.com/wwpc/nl/nl...3-3445275.html
Lijkt het je dan niet verstandiger om een nieuwere versie te nemen die bij een 2de hands verkoop dan nog een hogere waarde zou hebben ?
Ben trouwens benieuwd wat voor producten erbij komen als 3Com helemaal van HP is.
Laatst gewijzigd door KristianT; 08/01/10 om 19:25.
Vandaag ging het resetten naar de fabrieksinstellingen bij een van onze 1810 switches niet helemaal zoals het hoort. Gezien er geen VOID stikker op de 1810 zit ben ik eens gaan kijken in de behuizing. Nu schept mijn verbazing dat een 10 pin connector op de printplaat zit, waarbij "console" staat. Heeft iemand hier ervaring met dergelijke connectoren?
Ik heb een paar foto's geschoten en toegevoegd.

Ik denk dat dit enkel een voorbereiding is op de print, Milan. Geen daadwerkelijk gebruik.
Voor zover ik weet hebben deze switches geen console aansluitingen helaas. Is webmanaged.
Question 1: What type of management is available for the ProCurve 1810G Series Switches?
Answer: The 1810G Series Switches are Web Managed switches. This means that the Web interface is the only method for managing and configuring the switch. The 1810G Series Switches have a user-friendly Web interface and are designed to allow users to add basic capabilities to their infrastructure without adding complexity. The 1810G Series Switches do not have a console port or command line interface.
Dat chipje bij de connector met "CONSOLE" is een RS232 interface converter. Je kunt op die 10 polige connector gewoon zo'n kabeltje zetten die ook in PC's zit. Geen idee wat je er dan mee kunt, maar het kan geen kwaad. Vaak zit zo iets wel op de print maar niet op de buitenkant.

Past inderdaad, maar denk niet dat je er dan nog veel mee kunt. De switch heeft verder geen commandline
Wat ik persoonlijk toch wel heel erg prettig vind om te hebben. Veel beter configgen (vooral met vlans etc). Minder kans op config problemen doordat de webbrowser crasht (wat Milan denk ik ook heeft gehad).
Maar ik zie dat dit ook al een paar keer rond is gegaan in dit topic![]()
Laatst gewijzigd door ichosting; 15/06/10 om 23:43.

Meestal worden deze interne console poorten gebruikt om firmware updates te doen bij switches/router waar het via webinterface verkeerd gelopen is. Heb ooit eens van cisco/linksys een manual gehad om dit bij een router te doen, dus zal bij HP wel ook zo iets dergelijks zijn. Normaal zou je bootup moeten kunnen zien via console en single user mode om firmware te doen en daar blijft het dan meestal ook bij (meestal met combinatie van reset ofzo indrukken bij opstarten om in die mode te geraken).
Dennis de Houx - All In One ~ Official ISPsystem partner
Lees hier de webhostingtalk.nl forum regels en voorwaarden!
Zolang je niet naar de andere kant van de print kijkt kunnen het net zo goed connectortjes zijn die ze illegaal dumpen
Als het een console is en het is connected (zie andere kant) kun je er (met een beetje baudrate en bit geknutsel) meestal nog wel iets uit krijgen.
Console funtionaliteit op een switch kost in massaproductie een paar euro om te bouwen dus wellicht is het al werkend en is de switch gewoon voor een andere doelgroep ontwikkeld (same print, ander doosje).
SystemDeveloper.NL - 64BitsWebhosting.EU : Softwareontwikkeling & Hosting freaks
Kan verbinding maken met 9600 baud. Resultaat:
Code:PIOK FF410040=87400000 FF410048=071041B8 CFE-NTSW-5.0.3 for BCM953314R24GS (32bit,SP,BE,MIPS) SP CFE Version: P.1.4 Build Date: Mon Jun 8 13:47:19 IST 2009 ([email protected]) Copyright (C) 2000,2001,2002,2003,2004,2005 Broadcom Corporation. Initializing Arena. Initializing Devices. Board : BCM953314R24GS CPU type 0x29050: 200MHz Total memory: 0x1000000 bytes (16MB) Total memory used by CFE: 0x80EB4000 - 0x80FFFF80 (1359744) Initialized Data: 0x80EFB718 - 0x80EFC510 (3576) BSS Area: 0x80EFC510 - 0x80EFDF70 (6752) Local Heap: 0x80EFDF80 - 0x80FFDF80 (1048576) Stack Area: 0x80FFDF80 - 0x80FFFF80 (8192) Text (code) segment: 0x80EB4000 - 0x80EFAE77 (290423) Boot area (physical): 0x00E73000 - 0x00EB3000 Relocation Factor: I:E12B4000 - D:E12B4000 Compression Supported: 7zip MIPS is operating in SYNC mode CFE> help Available commands: copydisk Copy a remote disk image to a local disk device via TFTP test fatfs Do a FAT file system test test disk Do a disk test, read/write sectors on the disk @ Boot VxWorks c Change the VxWorks boot string p Parse and display VxWorks boot string M Show or set Ethernet MAC address ptable save Save flash partition table. ptable clear Clear flash partition table. ptable del Delete flash partition table. ptable add Delete flash partition. ptable show Show flash partition table. etx start eth loopback application lbtest start eth loopback application ethstat eth drv stats cpw write p0 register ttlb test TLB tdc test data cache flprobe Probe flash erase Serial Flash erase one sector flush Serial Flash read cache flush sflashw Serial Flash write sflashr Serial Flash read miiw MII write miir MII read scr Schan write scw Schan write envdev set environment device reset Reset the system. nvram import Import nvram variables from standard environment. nvram erase Delete all nvram variables. nvram commit Commit nvram variable bindings. nvram show Show all nvram variables. nvram unset Delete an nvram variable. nvram set Set the value of an nvram variable. nvram get Get the value of an nvram variable. set console Change the active console device sleep Wait for some period of time loop Loop a command flash Update a flash memory device memtest Test memory. f Fill contents of memory. e Modify contents of memory. d Dump memory. u Disassemble instructions. reserve Mark a region of memory as reserved autoboot Automatic system bootstrap. batch Load a batch file into memory and execute it go Start a previously loaded program. boot Load an executable file into memory and execute it load Load an executable file into memory without executing it save Save a region of memory to a remote file via TFTP ttcp TCP test command. tcp constest tcp console test. tcp listen port listener. tcp connect TCP connection test. rlogin mini rlogin client. ping Ping a remote IP host. arp Display or modify the ARP Table ifconfig Configure the Ethernet interface device Erase the flash devices show flash Display information about a flash device. show boot Display boot block from device, show config Dump CP0 configuration registers show heap Display information about CFE's heap show memory Display the system physical memory map. show devices Display information about the installed devices. clearenv Clear environment variables. unsetenv Delete an environment variable. printenv Display the environment variables setenv Set an environment variable. help Obtain help for CFE commands For more information about a command, enter 'help command-name' *** command status = 0 CFE>

Heb net ook even google gekeken of er info over is. Hierbij kreeg ik het volgende:
http://www.happyhacking.org/Happy_Ha...0G_Take_2.html
Ik zou sowieso even de firmware flashen naar 1.17. Webbased kun je de snmp dan ook uitzettten en de community string wijzigen.
SystemDeveloper.NL - 64BitsWebhosting.EU : Softwareontwikkeling & Hosting freaks
Heb het kunnen fixen. Het bleek dat alle nvram settings uit de firmware waren. Deze heb ik handmatig toe kunnen voegen door middel van "nvram set var=":
Daarna sla je de wijzigingen op middels "nvram commit" en reset je de switch met "reset -yes -sysreset"Code:STARTUP="boot -z -elf flash0.os1:" et0macaddr=reboot image1_size=1689146 sdram_config=0x0000 sdram_refresh=0x0000 clear_config=0 SP_Cfe_Version=P.1.4 sdram_init=0x000A serial=0000000000 image2_size=1681886 serial_number=12345 sdram_ncdl=0x00000000
Voor degene die dit probleem tegen komt.