Heb trouwens vandaag de HP 1800 ook maar aangeschaft :)
Afdrukvoorbeeld
Heb trouwens vandaag de HP 1800 ook maar aangeschaft :)
Ik lees net op de HP site dat deze uit de productie genomen zijn.
http://h10010.www1.hp.com/wwpc/nl/nl...3-3445275.html
Lijkt het je dan niet verstandiger om een nieuwere versie te nemen die bij een 2de hands verkoop dan nog een hogere waarde zou hebben ?
Ben trouwens benieuwd wat voor producten erbij komen als 3Com helemaal van HP is.
1800's zijn net zo goed hoor en het blijven goedkope gigabitswitches =)
Vandaag ging het resetten naar de fabrieksinstellingen bij een van onze 1810 switches niet helemaal zoals het hoort. Gezien er geen VOID stikker op de 1810 zit ben ik eens gaan kijken in de behuizing. Nu schept mijn verbazing dat een 10 pin connector op de printplaat zit, waarbij "console" staat. Heeft iemand hier ervaring met dergelijke connectoren?
Ik heb een paar foto's geschoten en toegevoegd.
Ik denk dat dit enkel een voorbereiding is op de print, Milan. Geen daadwerkelijk gebruik.
Voor zover ik weet hebben deze switches geen console aansluitingen helaas. Is webmanaged.
Citaat:
Question 1: What type of management is available for the ProCurve 1810G Series Switches?
Answer: The 1810G Series Switches are Web Managed switches. This means that the Web interface is the only method for managing and configuring the switch. The 1810G Series Switches have a user-friendly Web interface and are designed to allow users to add basic capabilities to their infrastructure without adding complexity. The 1810G Series Switches do not have a console port or command line interface.
Dat chipje bij de connector met "CONSOLE" is een RS232 interface converter. Je kunt op die 10 polige connector gewoon zo'n kabeltje zetten die ook in PC's zit. Geen idee wat je er dan mee kunt, maar het kan geen kwaad. Vaak zit zo iets wel op de print maar niet op de buitenkant.
Past inderdaad, maar denk niet dat je er dan nog veel mee kunt. De switch heeft verder geen commandline :)
Wat ik persoonlijk toch wel heel erg prettig vind om te hebben. Veel beter configgen (vooral met vlans etc). Minder kans op config problemen doordat de webbrowser crasht (wat Milan denk ik ook heeft gehad).
Maar ik zie dat dit ook al een paar keer rond is gegaan in dit topic :)
Meestal worden deze interne console poorten gebruikt om firmware updates te doen bij switches/router waar het via webinterface verkeerd gelopen is. Heb ooit eens van cisco/linksys een manual gehad om dit bij een router te doen, dus zal bij HP wel ook zo iets dergelijks zijn. Normaal zou je bootup moeten kunnen zien via console en single user mode om firmware te doen en daar blijft het dan meestal ook bij (meestal met combinatie van reset ofzo indrukken bij opstarten om in die mode te geraken).
Zolang je niet naar de andere kant van de print kijkt kunnen het net zo goed connectortjes zijn die ze illegaal dumpen :)
Als het een console is en het is connected (zie andere kant) kun je er (met een beetje baudrate en bit geknutsel) meestal nog wel iets uit krijgen.
Console funtionaliteit op een switch kost in massaproductie een paar euro om te bouwen dus wellicht is het al werkend en is de switch gewoon voor een andere doelgroep ontwikkeld (same print, ander doosje).
Kan verbinding maken met 9600 baud. Resultaat:
Code:PIOK FF410040=87400000 FF410048=071041B8
CFE-NTSW-5.0.3 for BCM953314R24GS (32bit,SP,BE,MIPS)
SP CFE Version: P.1.4
Build Date: Mon Jun 8 13:47:19 IST 2009 ([email protected])
Copyright (C) 2000,2001,2002,2003,2004,2005 Broadcom Corporation.
Initializing Arena.
Initializing Devices.
Board : BCM953314R24GS
CPU type 0x29050: 200MHz
Total memory: 0x1000000 bytes (16MB)
Total memory used by CFE: 0x80EB4000 - 0x80FFFF80 (1359744)
Initialized Data: 0x80EFB718 - 0x80EFC510 (3576)
BSS Area: 0x80EFC510 - 0x80EFDF70 (6752)
Local Heap: 0x80EFDF80 - 0x80FFDF80 (1048576)
Stack Area: 0x80FFDF80 - 0x80FFFF80 (8192)
Text (code) segment: 0x80EB4000 - 0x80EFAE77 (290423)
Boot area (physical): 0x00E73000 - 0x00EB3000
Relocation Factor: I:E12B4000 - D:E12B4000
Compression Supported: 7zip
MIPS is operating in SYNC mode
CFE> help
Available commands:
copydisk Copy a remote disk image to a local disk device via TFTP
test fatfs Do a FAT file system test
test disk Do a disk test, read/write sectors on the disk
@ Boot VxWorks
c Change the VxWorks boot string
p Parse and display VxWorks boot string
M Show or set Ethernet MAC address
ptable save Save flash partition table.
ptable clear Clear flash partition table.
ptable del Delete flash partition table.
ptable add Delete flash partition.
ptable show Show flash partition table.
etx start eth loopback application
lbtest start eth loopback application
ethstat eth drv stats
cpw write p0 register
ttlb test TLB
tdc test data cache
flprobe Probe flash
erase Serial Flash erase one sector
flush Serial Flash read cache flush
sflashw Serial Flash write
sflashr Serial Flash read
miiw MII write
miir MII read
scr Schan write
scw Schan write
envdev set environment device
reset Reset the system.
nvram import Import nvram variables from standard environment.
nvram erase Delete all nvram variables.
nvram commit Commit nvram variable bindings.
nvram show Show all nvram variables.
nvram unset Delete an nvram variable.
nvram set Set the value of an nvram variable.
nvram get Get the value of an nvram variable.
set console Change the active console device
sleep Wait for some period of time
loop Loop a command
flash Update a flash memory device
memtest Test memory.
f Fill contents of memory.
e Modify contents of memory.
d Dump memory.
u Disassemble instructions.
reserve Mark a region of memory as reserved
autoboot Automatic system bootstrap.
batch Load a batch file into memory and execute it
go Start a previously loaded program.
boot Load an executable file into memory and execute it
load Load an executable file into memory without executing it
save Save a region of memory to a remote file via TFTP
ttcp TCP test command.
tcp constest tcp console test.
tcp listen port listener.
tcp connect TCP connection test.
rlogin mini rlogin client.
ping Ping a remote IP host.
arp Display or modify the ARP Table
ifconfig Configure the Ethernet interface
device Erase the flash devices
show flash Display information about a flash device.
show boot Display boot block from device,
show config Dump CP0 configuration registers
show heap Display information about CFE's heap
show memory Display the system physical memory map.
show devices Display information about the installed devices.
clearenv Clear environment variables.
unsetenv Delete an environment variable.
printenv Display the environment variables
setenv Set an environment variable.
help Obtain help for CFE commands
For more information about a command, enter 'help command-name'
*** command status = 0
CFE>
Heb net ook even google gekeken of er info over is. Hierbij kreeg ik het volgende:
http://www.happyhacking.org/Happy_Ha...0G_Take_2.html
Ik zou sowieso even de firmware flashen naar 1.17. Webbased kun je de snmp dan ook uitzettten en de community string wijzigen.
Heb het kunnen fixen. Het bleek dat alle nvram settings uit de firmware waren. Deze heb ik handmatig toe kunnen voegen door middel van "nvram set var=":
Daarna sla je de wijzigingen op middels "nvram commit" en reset je de switch met "reset -yes -sysreset"Code:STARTUP="boot -z -elf flash0.os1:"
et0macaddr=reboot
image1_size=1689146
sdram_config=0x0000
sdram_refresh=0x0000
clear_config=0
SP_Cfe_Version=P.1.4
sdram_init=0x000A
serial=0000000000
image2_size=1681886
serial_number=12345
sdram_ncdl=0x00000000
Voor degene die dit probleem tegen komt ;).